Short answer: clean every trace of powder off the print, heat a bath of dye made for synthetic fabrics to just below boiling, keep the piece moving in it until the color is a shade darker than you want, then rinse, wash and dry. Nylon takes dye readily, so most of the skill lies in getting the color even and being able to repeat it.
Why nylon prints can be dyed
SLS prints in PA 12 nylon come out of the printer white and slightly porous. Nylon is the same material as many fabrics, and it absorbs fabric dye into the surface instead of holding it on top like paint. That's why dyed nylon jewelry doesn't chip or peel. It's also why color can't be touched up later, which is covered in Can nylon jewelry be repaired?
One limit to know first: some printing processes, such as multi jet fusion (MJF), produce gray parts. A gray part can only be dyed darker, and in practice that usually means black. For bright or pale colors you need a white print.
Choosing a dye
- Dyes for synthetic fabrics, such as Rit DyeMore and iDye Poly, are made for nylon and polyester and are the easiest place to start. They're sold in craft stores and can be mixed to make custom shades.
- Acid dyes, such as Jacquard Acid Dye, are the classic dye for nylon and wool. They come in a wider range of colors and need an acid (white vinegar or citric acid) in the bath to fix.
- All-purpose dyes also work on nylon but are less concentrated than the synthetic versions.
Whichever you choose, check that the label says it works on nylon.
What you need
- A stainless steel or enamel pot used only for dyeing, never for food
- A stove or hot plate, and a cooking or candy thermometer
- Dye, plus white vinegar or citric acid if you're using acid dye
- Tongs or a slotted spoon, and a mesh bag or strainer basket for small pieces
- Rubber gloves, an apron, and good ventilation
- Mild dish soap, an old soft toothbrush and paper towels
- A few test pieces printed in the same material: offcuts, test chips or failed prints
How to dye nylon at home, step by step
- Clean the print thoroughly. Brush and rinse out every bit of loose powder, especially in holes, gaps and lattices. Then wash the piece in warm water with a drop of dish soap. Leftover powder and skin oils are the main cause of blotchy color.
- Soak it in warm water for a few minutes. A wet piece takes dye more evenly than a dry one.
- Heat the bath. Fill the pot with enough water for the piece to move freely, and heat it to just below boiling, around 80 to 90 °C (175 to 195 °F). Stir in the dye, plus the acid if your dye calls for it, following the dye maker's instructions. Nylon absorbs dye quickly, so you can start with a little less dye than the label suggests.
- Put the piece in, and keep it moving. Stir or swish it constantly so it never rests in one spot. Keep it off the bottom of the pot, which is hotter than the water: a mesh bag or basket helps. Watch thin parts in particular, because hot nylon softens slightly.
- Check the color. Lift the piece out and rinse a test chip, or the piece itself, under the tap every few minutes. Wet nylon looks darker than it will dry, so stop when it's a shade darker than your target. Depending on the dye and the color, that can take anywhere from a couple of minutes to half an hour.
- Rinse until the water runs clear, first in warm water, then cool.
- Wash it once more with mild soap to remove any dye still sitting on the surface, then rinse again.
- Dry it completely on a paper towel, out of the sun, before you fit findings or wear it.
Getting even color
- Blotches or spots: usually leftover powder or oil. Clean better next time; for now, a second bath can even out light patches.
- Darker on one side: the piece rested against the pot or stayed still. Keep it moving.
- Light inside holes and lattices: the dye couldn't flow through. Swish the piece so the bath passes through the openings.
- Too dark: you can't easily take color out of nylon, so it's better to creep up on a shade than to overshoot. A darker color, or black, can always go on top.
- Layer lines show more after dyeing: dye can pick out the steps on surfaces that were almost flat in the printer. Changing the print orientation helps. Designing jewelry for SLS printing
Dyeing in the studio
For one-off pieces, the kitchen method is enough. When you're selling, the challenge changes: color has to be repeatable, so a customer who orders a second earring, or a matching necklace, gets the same shade. Studio dyeing is mostly about controlling every variable:
- Measure everything. Weigh the dye and acid, measure the water, and keep the temperature steady with a thermostatic hot plate instead of a stove.
- Write down every recipe: dye, amount, water volume, temperature, time, and the date. Your record book becomes your color palette.
- Dye a test chip with every batch and keep it with the recipe. Compare new batches against it.
- Dye matching pieces together. Earrings that go into the same bath at the same time match. Pieces dyed a week apart may not.
- Replace the bath once it has been used heavily. Exhausted dye shifts the color.
At production scale, studios and print services use industrial dyeing machines, made by companies such as DyeMansion, that control temperature, time and dye dosing automatically. Many print services also offer dyeing in a set range of colors, which is the easiest route if their palette suits your work.
Does dyed nylon fade?
Dye goes into the material, so it doesn't wear off in normal use. Long exposure to direct sunlight can fade it over time, which is why care guides recommend storing pieces out of the sun. Nylon jewelry care guide
Safety
- Keep dyeing equipment separate from kitchen equipment, permanently.
- Wear gloves; dye stains skin and countertops.
- Work with ventilation, and avoid breathing dye powder when you measure it.
- Follow the safety instructions on the dye you buy.