Short answer: make walls at least 1 mm and struts closer to 1.5 mm, leave about 0.5 mm between parts that need to move, put holes and escape holes in early, think about which way the piece will sit in the printer, and size rings by their inner diameter with a little allowance for a thicker band. The rest of this guide explains each rule and why it matters for jewelry in particular.
The published minimums come from print services and are written for engineering parts. Jewelry is thinner, gets worn every day, is tumbled and dyed after printing, and gets dropped on tiles. So treat the minimums as the place where failures start, not as a design target.
How SLS shapes your design
In selective laser sintering, a laser fuses a bed of nylon powder (usually PA 12) one thin layer at a time. The unfused powder around the piece holds it up while it prints, so you don't need supports. That is why SLS can print lattices, chains and parts that already move, all in one build. It also means every rule below comes from three facts:
- Powder has to come out. Anything enclosed, narrow or tight traps powder, and trapped powder can fuse.
- Heat spreads. The laser warms the powder next to what it's fusing, so very thin walls and very small gaps don't print the way they were drawn.
- Finishing removes material. Tumbling, blasting and dyeing round off edges and soften the finest detail.
Wall thickness
Most print services quote a minimum wall of about 0.7 to 0.8 mm for PA 12. Some guides ask for 1 mm, and one recommends 1.3 mm for repeatable results. Walls that are too thin can also come out thicker than drawn, because heat from the laser fuses extra powder onto them.
For jewelry, a practical starting point is:
- 1.0 mm for walls and surfaces supported on more than one side.
- 1.2 to 1.5 mm for struts, arms and lattice members that are free on one end or take load, such as anything that holds a finding.
- 2 mm or more around a hole that a jump ring or ear wire passes through. That ring of material carries all the pull.
- A little extra on any piece that will be tumbled, because tumbling removes material from edges and corners first.
Thicker isn't always better. Very thick, solid sections waste material and add weight. A ring band or a large pendant can be hollowed out, with escape holes added (see below).
Clearances for moving parts
Chains, hinges, rotating elements and interlocked links can be printed already assembled. The catch is the gap. If it's too small, powder fuses inside it and the parts come out welded together.
Published figures range from 0.3 mm to about 0.6 mm. Several services recommend 0.5 mm for parts printed inside each other. Dense volumes nearby can harden the powder between surfaces, so a gap next to a thick section may need more.
For jewelry:
- 0.5 mm is a good default between any two surfaces that must move apart.
- Go up to 0.6 or 0.7 mm where the gap is long, enclosed, or next to a heavy section.
- Design the movement to free itself. A link that can rotate and slide lets powder fall out; a pin in a tight, deep hole traps it.
- Print a test piece with a few gaps side by side (0.4, 0.5, 0.6, 0.7 mm) on your service and your material. It costs little and settles the question for good.
Holes, escape holes and detail
- Holes: design them at least 1.5 mm across so powder doesn't get stuck in them. Round holes can also shrink a little during sintering, so draw jump-ring holes slightly larger than the wire.
- Escape holes for hollow parts: a hollow piece holds a cavity full of loose powder. The usual advice is at least two holes of 3.5 mm or more on opposite sides. On jewelry, put them where they'll be hidden, such as inside a ring band or on the back of a pendant.
- Engraved and raised detail: aim for about 1 mm of depth or height if it needs to survive finishing. A maker's mark or signature should be engraved, in a sans-serif font, at least about 2 mm tall.
Orientation
Because SLS needs no supports, orientation is about looks and strength, not about whether the piece will print. The printer builds in layers roughly a tenth of a millimeter thick, and how those layers cross your surfaces shows up in the finished piece.
- Shallow curves show steps. A surface that is almost flat to the build plate shows the layers as faint contour lines, which dye can make more visible. Tilting the piece so the main show surface isn't nearly flat usually helps.
- Large flat areas can warp as they cool. Setting a flat pendant at an angle rather than flat in the bed reduces the risk.
- Long, thin elements are best kept out of a vertical position where possible, and their weakest direction shouldn't be the one that takes the load in wear.
- Not every service lets you choose. Many place parts automatically to fill the build. If orientation matters for a piece, ask before you order.
Sizing
Rings
Size a ring by its inner diameter. US sizes step by about 0.8 mm: size 6 is about 16.5 mm, size 7 about 17.3 mm, size 8 about 18.1 mm and size 9 about 18.9 mm. A useful formula is inner diameter (mm) ≈ 11.63 + 0.8128 × US size.
Two things make printed rings fit differently from metal ones:
- Bands are thicker. To be strong enough, a nylon band is usually wider and thicker than a metal one, and wide bands feel tighter. Many makers add a little to the inner diameter, or recommend sizing up, for wide designs.
- Tolerance. Services typically quote accuracy around ±0.3 mm (or ±0.3%, whichever is larger), which is a noticeable share of one ring size. Print a sizing ring in your process before selling a size range.
Earrings, pendants and weight
Laser-sintered PA 12 is a little less dense than water, so a design's volume in cubic centimeters is a fair estimate of its weight in grams. Your CAD program reports the volume, which lets you check the weight of a large earring before you print it. Remember to add the findings.
Bracelets and wearability
A rigid bangle has to pass over the hand, not just fit the wrist, so measure across the knuckles with the hand folded. Printed nylon flexes slightly, which helps cuffs and open forms but isn't enough to make a closed bangle stretch.
Findings and joins
Nylon can't be soldered, so every connection to metal is mechanical or glued. Plan it in the model:
- Jump-ring and ear-wire holes sized for the wire, with at least 2 mm of material around them.
- Sockets for posts that hold the finding by shape, such as a captured head, a thread or a rivet, rather than relying on glue alone.
- Room for the tool: pliers need space to open and close a jump ring after printing.
Pieces with well-designed, replaceable findings are also the easiest to repair later. Can nylon jewelry be repaired?
A checklist before you upload
- Walls at least 1 mm; load-bearing struts 1.2 to 1.5 mm.
- Moving parts at least 0.5 mm apart, with a way for powder to escape.
- Holes at least 1.5 mm; hollow parts with two escape holes of 3.5 mm or more.
- Engraved marks about 1 mm deep.
- Show surfaces not nearly flat to the build plate; large flat pieces angled.
- Rings sized by inner diameter, with an allowance for wide bands.
- Weight checked from the volume, findings included.
- Mesh is watertight (closed, no holes or flipped faces), in millimeters.
- A test print of anything new, in the material and color you'll sell.
Every service publishes its own guidelines, and they differ. When this guide and your service disagree, follow the service for that printer.